Search results

Hey guys. I need some help ASAP please. I got a crrossfire xz250r off a kid n the wiring is a complete mess on it. Would anyone be able to tell me a simple way to throw some wires together to get it to run? I don't care about the elec start so I don't need the starter solenoid and so on I...

Torco RFF Racing Fork Fluid 10 ^^^^ that oil and I'm 80 kilos

i tried that and it stopped a bit but still seeping a little bit. either way it still lost a lot of oil, so does anyone know how much it is supposed to have in them and where to put it in??

does anyone have a tutorial on how to replace fork seals and how much oil to put back in? i got new ones because my old ones are leaking (tried cleaning the dirt out but still leaked). i don't know much about forks so i don't want to go ripping them apart and not know how to put them back...

hey guys i got a dhz 140 dpro and have been doing a lot of freestyle on it lately and pretty large ramps. will my bike be ok to do it on or should i look at strengthening the frame? I've already strengthened the frame where the shock bolts on cos it bent on me. cheers guys

i just compared the timing marks to the same one on my 140 outlaw, and before looking at the outlaw my timing didnt look to be out, but after comparing it, it is definately out! lol. but i cant get the flywheel off the check the rubber.

yea cleaned all the kets with compressed air

hey guys, my dhz140 dpro is running really crap! first, it blows blue smoke and uses a bit of oil, this doesn't worry me, unless it is related to my next issue. when i start it it idles fine, but i go to give it a rev and it just dies and splutters and carry on. this happens both stationary and...

mate, your a legend! thanks heaps!

hey guys. done some searching and havent found anything. does anyone have or know of a tutorial on how to replace valves?? not just adjust clearances, i wanna know how to actually replace them. Cheers, Baldwin.

i'm not sure, but im quite confident i got it on now. i put it above the cog on the right. you cant see in the photo, but it has like teeth in the centre of the cog so it lines up with the long teeth on the shaft. thank you very much for your help mate! you really dont know how much i...

ok so im pretty sure i have the 2 copper washers and the two cogs on the right of the photo correctly on the shafts, but i got no clue where the cog on the left goes. it has no holes or dog teeth at all in it, and it wont fit on the left shaft as the hole isnt wide enough

thanks very much mate! i will try that!

hey guys. sorry to be a pain but i really need to know a few things to help me put my crank case back together (have been searching the site all day and havent found any help really). i pulled it down to fix a pretty big leak in the left crank case (fixed now) and i thought i remembered how...

yea will definately be strengthening the frame! will have the make it go around the head tho, because the head is only about a centimeter off hitting to front wheel as it is when the shocks are compressed. will make gettin the engine out hard if i ever have to. and yes the sprocket lines up,was...

went along with it out of boredom and time off work. coming along very well actually!

yea i got a dpro 140 and a few other bikes just thought it might be a fun little project cause i got the whole cr, except to motor and a got the whole tdr except its basically stuffed besides the engine

hey. so i got a tdr125 and the frame and forks and everythingfell apart. i got an old cr80 frame (1984 i think). in going to put the 125 motor into it, has anyone done anything like this before and would you have any photos icould have a look at??

ive got a perfectly good spare shaft, i just havent needed to use it.

very nice mate!! with my ds, i'm not sure if you would like to risk doing to to yours, i loosened the bolt on the kick start, drilled a hole so it was half drilled onto the kick start, half into the shaft, screwed a self tapper screw into it, then tightened the **** out of the kick start bolt...