MY LXR 180cc

[winky34]

thanks mate !!!

 

[winky34]

doesn't matter what the exhaust is made from lol...... bigger jets = problem solvered..

they are the biggest jets you can get for that carby.

 

[winky34]

uote=winky34;314105]hey mate, its because the pipe is made from thin gauge stainless steel, and will glow of a night when the bike is stationary.

if using normal gauge mild steel header, it wont glow as much

incase anyone else misses it...

wicked lookin bike mate!! could light a smoke off the exhaust![/QUOTE]

thanks mate, yeah you could haha

 

[foolsp33d]

ten bucks says a bit of 2mm stainless vs a bit of 2mm steel the stainless burns thru and glows red quicker than the 'standard' steel... jetting MAY have something to do with it.. but being the $ and time the OP has put into the bike, I dare say his jetting is on the mark...

 

[wogtaz ryder]

Ummm no , you can go way bigger then that with that carby..

 

[DHZ_XR8cing]

Id say an air leak some where.Either inlet or exhaust side.

 

[winky34]

Ummm no , you can go way bigger then that with that carby..

please send me a link or address or contact to buy these jets to suit my OKO carby ?

 

[wogtaz ryder]

ten bucks says a bit of 2mm stainless vs a bit of 2mm steel the stainless burns thru and glows red quicker than the 'standard' steel... jetting MAY have something to do with it.. but being the $ and time the OP has put into the bike, I dare say his jetting is on the mark...

its a bolt on $500 exhaust ... hasn't put any more effort in then any other guy , just abit of money .. i still say jetting DEFINITELY has a major part in it..

 

[wogtaz ryder]

OKO Australia - Flatslide Carburettors

 

[winky34]

Id say an air leak some where.Either inlet or exhaust side.

with the boost bottle it has to stablelize it then richen up the mixture of air and atomized fuel, basically leting in more air than normal

 

[winky34]

OKO Australia - Flatslide Carburettors

didnt realize because i have been getting parts from another supplier, they were the biggest he had, thanks

 

[winky34]

its a bolt on $500 exhaust ... hasn't put any more effort in then any other guy , just abit of money .. i still say jetting DEFINITELY has a major part in it..

unsure about what you point was with this comment ?

 

[winky34]

i would agree with the jetting comment if the pipe was glowing while racing, and when checking the plug tip at the end of racing it is pale brown, usally is a good sign jetting is spot on, and the bike runs very cleanly on and off acceliration

 

[wogtaz ryder]

usually a good sign the main jet is good .... if you where running it wide open in a race .... means nothing more really..

a bike with to small a jet will still run nice and crisp , doesn't mean its spot on.

 

[DHZ_XR8cing]

Id be getting rid of that "boost" bottle and see what the exhaust does

 

[winky34]

usually a good sign the main jet is good .... if you where running it wide open in a race .... means nothing more really..

a bike with to small a jet will still run nice and crisp , doesn't mean its spot on.

in your opinion what jetting size should i use ?
also how do i tell it is running spot on ?
obviously you have a concern with the glowing header, you must relize the bike was held on the limiter at that time, also should the bike be blowing blue flame while on the limiter ?

 

[winky34]

Id be getting rid of that "boost" bottle and see what the exhaust does

i understand that the bottle causes the leaness while stationary on the limiter but it only runs lean/glows for 25secs, check the video

 

[DHZ_XR8cing]

On the limiter?? Why are you doing that to the point that your exhaust is glowing??

 

[winky34]

On the limiter?? Why are you doing that to the point that your exhaust is glowing??

i need to warm up the bike quickly due to cold night racing and the bike hadden been riden for a hour and a half, prior to the last race, if bike not up to tempreture quickly its a bit flat off the start

 

[rach88]

please send me a link or address or contact to buy these jets to suit my OKO carby ?

I have a set of OKO mains like 95s to 120's set of 10 you can have for 20 bucks... brand new never used! lol I have a kehlien pe and they don't fit No dodgy reasons for wanting to sell them!