Motovert Type R, 201cc

[gottagetacheaperhobby]

No o rings with it, and the sight glass is 25mm.
Which lip do you mean craig? Will have a go it when im sure which one you mean lol
I am making a start on polishing the stator cover now, i recon i will leave the clutch case as it is, i was looking over the clutch case i polished for callums old 160, and remembering how painful it was lol when i pick a colour scheme for the bike i might paint it see what happen lol

Sent from my SM-T110 using Tapatalk

 

[my67xr]

The first lip (3mm flat edge ) as the air goes into the carb, like this one

 

[gottagetacheaperhobby]

Thanks mate, will get onto that one is that your oko off the 190?

Sent from my SM-T110 using Tapatalk

 

[my67xr]

The Lifan 150 oil filter o'ring is roughly 44mm i/d, and the Oil sight window fit's into a 25mm hold in the side cover


Yeah that's the Oko 30mm, i think i polished it a bit more after those shot's



It looked like this originally

 

[gottagetacheaperhobby]

Bike now has braaap/ycf billet hubs installed, took me a while to get the rear to fit but its in
Greased the linkage bearings, which has removed the play that had started to develop, and got a little more done on the stator cover

Sent from my SM-T110 using Tapatalk

 

[gottagetacheaperhobby]

Bit more progress on this blasted stator cover, starting to see results now.

Sent from my SM-T110 using Tapatalk

 

[my67xr]

A box of part's arrived this morning from Jaimie at Classic Honda 50's, thank's mate



It was full of TB goodness !!

 

[gottagetacheaperhobby]

Hey hey thats very nice to see

Sent from my SM-T110 using Tapatalk

 

[gottagetacheaperhobby]

So gasket set, kick start gears and oil cooler lines arrived. To bad i ordered 10mm banjo fittings thinking the yx ran 10mm ones so the oil cooler lines are useless :/ luckily that means the push on barbs i have on the 160ho bottom end will work being 8mm

Sent from my SM-T110 using Tapatalk

 

[gottagetacheaperhobby]

How is things going your end craig?

Sent from my SM-T110 using Tapatalk

 

[my67xr]

Sorry thing's were a bit slow last week or so (health problem's), hopefully i can get into it next week and finish it off.

 

[gottagetacheaperhobby]

Sorry thing's were a bit slow last week or so (health problem's), hopefully i can get into it next week and finish it off.

Dont be sorry mate, i was just wondering how things were looking. Hope your ok, get to the engine when you can, im not stressed, as i said, was just curious

Sent from my SM-T110 using Tapatalk

 

[gottagetacheaperhobby]

Another boring update lol
Kick start arrived today

Sent from my SM-T110 using Tapatalk

 

[motorman]

Man can't wait to see it going!!!

 

[gottagetacheaperhobby]

Clutch cover o ring showed up today so now im all set on my end. Once craig is done with the case boring and head porting i will be braaap braaap once more

Sent from my SM-T110 using Tapatalk

 

[Phil67]

Are you running a base gasket? The 201's run better without it or skim the jug to get the piston up the bore. I had a much higher comp piston in mine than the TB piston as well. I wonder where my old cases are as I know my old engine is not being used. Love that you are going 67mm mate, good stuff. 70mm next time!

 

[gottagetacheaperhobby]

They dont leak without the base gasket phil? If not i will go that way. Yours was a ooracing setup wasnt it?
It was a combination of your build and another that inspired me to try the 201 route

Sent from my SM-T110 using Tapatalk

 

[Trains]

Phil your bike had so much compression! It was insane! Ummm i think your cases either ended up with Damian in Shepp or at Buzz bikes

Sent from my HTC_0P6B6 using Tapatalk

 

[Snaptrax]

Nah Phil's motor is in some nugget 50 frame with a 160 top end on it.
I sold it to a guy and two week later he blew it up.
Got rebuilt back to a 160 for some random reason and got put in a 50 frame. I have been on the look out for that motor but I can't seem to find it.
It's a shame as I have the spare 201 kit still at my house.

 

[Phil67]

If not running a base gasket then you have to use yamabond or similar. Terry at FP has all the info on that. Mine was oo racing style, exactly the same but not from them. If my old motor is in that 50 frame then I know who has it.